首页 > 技术文章
美国笔补谤办别谤派克的执行器的部分技术参数：
根本的解决方法是要将派克笔础搁碍贰搁拆下,取出阀芯及阀芯套,用颁颁滨4清洗,使得阀芯在阀套内动作灵活。拆卸时应.
性能特点
产物类型 Single Vane | Double Vane
功能 Double
通孔尺寸 N/A
标准旋转（度数） 95°, 100°, 220°, 275° and 280°
扭矩范围（牛米） 0.69 to 30.96 (at 6 bar)
缓冲类型 Rubber Buffer
端口尺寸 M5 | G1/8 | G1/4
大工作压力（BAR) 10
运行环境温度 (C) -10 to +80
运行环境温度 (C) 14 to 176
遥感位置 Yes
重量（公斤） 0.16 to 2.05
耐腐蚀的选择 Yes
可修复 Yes
派克汉尼汾是美国财富250强公司,是运动与控制领域的。 在过往的百年中,派克汉尼汾在多元化工业市场和航空航天市场客户成功。派克的工程专业技能以及广泛...证书 No
美国笔补谤办别谤派克的执行器的部分技术参数：
PV rotary vane actuators provide the maximum amount of output torque from the smallest possible envelope size. Two basic styles are available. Single vane models have a maximum rotation of 280°, while the double vane units produce twice the torque output from identical envelope dimensions and have a maximum rotation of 100°. They convert pneumatic pressure into rotary motion for a wide variety of industrial applications. A short cylindrical chamber encloses a vane attached to a central shaft. Air pressure is applied to one side of the vane. The opposite side of the vane is connected to exhaust. This produces rotation of the vane and thus the central shaft. Due to vane actuator design there will always be some internal bypass in these units and therefore they should not be used as a brake or to support loads. Torque range from 0.69 to 30.96 at 6 bar.
■ Through rod facility size 22 and 33 : The two larger sizes of Vane Actuators are through rod as standard. The through rod facility enables linkages to be connected to both ends of the unit, maximising the design flexibility. This also enables the unit to be equipped with a kit providing full adjustment of the angle of rotation. The kit can be supplied complete with or without inductive sensors. These options can be assembled with the actuator when ordering or purchased as additional items.
■ Vane actuator with angle adjustment size 22 and 33 : This kit is assembled at the rear of the actuator and provides adjustment of :
- 0 to 100° for the double vane actuator
- 0 to 220° for the single vane actuator
The angle adjustment is attained by moving the end stops at the rear of the actuator. To facilitate this adjustment there is a position indicating disk on the rear face of the unit. Inductive sensors M8 with 90° plug-in and LED facility (PNP or NPN) can be added to the kit for end stop detection.
General Technical Data:
• International Standards : N/A
• Rotation Angles : 95°, 100°, 220°, 275° and 280°
• Versions : Double acting with:
Single vane - Not through rod
Double vane - Not through rod
Single vane - Through rod
Double vane - Through rod
• Cushioning : Rubber buffer
• Position Sensing : Inductive sensors M8 with 90° plug-in and LED facility (PNP or NPN) are available for sizes 22 and 33.
• Installation : Combination face and base mounting offer flexibility in application and design.
• Mounting Position : Any
Operating and Environmental Data:
• Operating Medium : For best possible service life and trouble-free operation dry, filtered compressed air to ISO 8573-1:2010 quality class 3.4.3 should be used. This specifies a dew point of +3°C for indoor operation (a lower dew point should be selected for minus temperature operation and we recommend the use of an inline dryer) and is in line with the air quality from most standard compressors with a standard filter.
• Operating Pressure : 2 to 10 bar maximum
• Operating Temperature : Standard temperature -10°C to +80°C
• Pre-lubricated : Further lubrication is normally not necessary. If additional lubrication is introduced it must be continued.
• Corrosion Resistance : High resistance to corrosion and chemicals.
Material Specification:
• End Covers : Hard anodised aluminium
• Cylinder Barrel : Hard anodised aluminium
• Shaft : Stainless steel
• Bearing : PTFE (Polytetrafluroethylene) coated bearing
• Vane : Hard anodised aluminium
• Seals : Nitrile
